Speaker Light Kits

Products:

Vendor's Website (External Link)

Spike 2 Kit and Acrylics

Spike 1 Kit

Stern/SAM Round and Square (7, 9)

Data East Kit (1-2)

Plastic Speaker Surrounds

Spike 2 Kit and Acrylics

Spike 2 Kit

Please utilize these install instructions for the Spike 2 Kit 11Speaker light kits

Installation Link (External)

For additional information on installation with the RGB Music Controller see the configuration information here and substitute the RGB Music IR controller for the white standard IR controller included with your kit.

Additional Information if you are using After Market Speakers

Using aftermarket speakers in your SPIKE 2 System game will work fine with the Speaker Light Kits. However, if they are aftermarket speakers that have spacer rings attached to the front of them, it will add some work to the process of installing them.

There is limited space behind the right speaker in SPIKE and SPIKE 2 System games because of the power transformer box. Due to this limited space, some aftermarket speakers that have attached spacer rings will not fit with the Speaker Light Kit frame. The only way to remedy this situation on these speakers is to carefully remove or cut down the spacer ring that is attached to the front of the speaker

If a Speaker Light Kit is being used in a game, the spacer ring is not needed, as the Speaker Light Kit light frame will then be used as the spacer that the speaker needs for its extended tweeter.

If SPIKE aftermarket speakers are bought directly from the Flipper Fidelity website, they have an option to buy them without the spacer rings by selecting "I have Speaker Lights" when ordering.

Keep in mind this space limitation and need to remove the spacer ring only effects Stern SPIKE and SPIKE 2 System games. Earlier Stern SAM (and Whitstar) System games have room to accommodate both the light kit frames and the aftermarket speakers with the attached spacer rings.

For tips on removing the spacer rings please see the "Aftermarket speakers in SPIKE System games" .pdf in the MANUALS SECTION.

Also note: Doing the spacer ring removal is done at your own risk. Neither I, nor the speaker manufacturer are responsible for any damage that may be caused by attempting to do so.

Along with making sure your speakers do not have the attached spacer rings on the front of them, you may also have to cut off the bars that run inside the speaker holes of the factory speaker plates. This will need to be done for any replacement speakers you are using that have tweeters that extend beyond the speaker's mounting points. The bars need to be removed so the speakers can mount flush on the speaker plates and the holes need to be open so the extended tweeters can go through the speaker plate's holes.

You may also choose to buy a set of replacement speaker plates for SPIKE 2 Speaker Light Kit use (sold separately). These replacement speaker plates will already have the bars removed from the speaker holes. The speakers will then be mounted to the replacement plates and the original factory speaker plates won't need to be modified or used at all.

Acrylics

Please utilize these installation tips for the frameless speaker acrylics for Spike 2 games

Installation tips 

Spike  1 (Kit 10)

Please utilize these install instructions for the Spike 1 Speaker light kits (round and square). 

Installation link (External)

Spike 1 Power adapter link (External)

For additional information on installation with the RGB Music Controller see the configuration information here and substitute the RGB Music IR controller for the white standard IR controller included with your kit.

Back to top

Stern Round and Square (Kits 7, 9)

Please utilize these install instructions for the Stern Round and Square Speaker light kits (round and square).

Installation link (External)

For additional information on installation with the RGB Music Controller see the configuration information here and substitute the RGB Music IR controller for the white standard IR controller included with your kit.

Back to top

Data East (Kit 1, 2)

Please utilize these install instructions for the Data East Speaker light kits (1 and 2). Please utilize the installation link below for steps 1-8A then utilize the Data East Power Adapter instructions for step 8B.

Installation link (External)

For additional information on installation with the RGB Music Controller see the configuration information here and substitute the RGB Music IR controller for the white standard IR controller included with your kit.